Dual Arm Articulating Wall Mount for 32″-56″ Plasma LCD 1019
- Dual Arms Ensure a Level Display
- Universal Design Fits Virtually Most 32″-56″ and Up To 140LBS
- Tilt Mechanism Offers 0 to 15 Degrees of Tilt
- Interface Size(H*W) 762 * 508mm or 30 * 20 inch, VESA 700×400 mm
- Adjusted left & right 120°
Heavy Duty Dual-Arm Wall Mount supports any Flat Screen Plasma or LCD Screen up to 140 pounds. For larger LCD and Plasma displays, the dual arms of the mount provide for a much more stable and level display as the arms are extended. A significant improvement over single arm designs Approximately 120 Degrees of side-to-side motion of the wall arms Supports 32″ 37″, 40″, 42″, 46″, 50″, 56″ LCD and Plasma TVs Up to 10 degrees of screen down tilt with easy to tighten screen tilt locking levers Rock solid wall arms extends flat screens to over 18″ away from the wall. The nested wall arms also fold inside each other when pushed flat to give the mount a very slim 3 1/2″ profile 18″ Wide wall plate supports block wall installation or installation on either 8″, 12″ or 16″ wall studs. The 1/8mm thick steel wall plate also has 2 pass through holes so that cables and cords can be fished into the wall interior for a clean installation look Security screws underneath mount allow the screens left to … More >>
Dual Arm Articulating Wall Mount for 32″-56″ Plasma LCD 1019
Like this post? Subscribe to RSS feed!
4 comments
Brad Hutchings on October 24, 2009 at 2:16 am
I spent more time researching the mount for my grandparents TV than I did the TV itself (Sony BRAVIA Z Series KDL-46Z5100 46-Inch 1080p 240Hz LCD HDTV). They had a 39 inch wide TV nook next to their fireplace, and we wanted the Sony to fit snug in front. I built a brace that goes across the nook about 9 inches from the front of it, using 2×6s attached to studs on the sides, and 2 2×4s spanning across and notched into the 2×6s. I attached this wall mount to the 2×4s, just as if there were a real wall back there.
This is a very solidly built mount. The Sony is 45 pounds, and it does not sag a bit with the arms extended all the way forward. The dual arm lets you adjust position laterally, forward and back, and some rotation side to side. Adjusting the tilt is easiest if you take the TV off the mount. A reasonably strong guy should be able to handle a 50 or 60 pound TV without assistance. The Sony, for example, is easy to grab. By contrast, my older XBR3 was awkward to grab.
I am giving this mount 5 stars despite one of the bottom screws being installed cross-threaded. A trip to the hardware store and 60 cents solved that. Installing a mount is pretty straight-forward. Find studs to bolt it into. Make sure it’s level. Blah blah. The instructions have good hieroglyphics, but the English is laughable. The screws and stuff are separated nicely into little plastic pockets labeled with letters, making it simple to follow the pictures and put it together.
Tip (1): When I got my brace built, mount attached, and TV up on the mount — a couple hours work — the 46″ set was slightly but noticeable off-level. Well, actually, it was pretty level, but the fireplace mantel wasn’t quite level and had some lines near the TV that made it look slightly off. I used a piece of felt under the left-top hanger to even things out. So don’t sweat it if you come out a little off, you can adjust that easily and cheaply.
Tip (2): I’d bet with a heavier TV, it would be easy to adjust the mount by pulling it in and out all the time, because you’d have some weight helping you. With a 50 pound TV, the mount doesn’t move at the touch of a finger. This kind of mount works best to put the TV into a position you’d like it to be in (mostly) permanently. If you’re just getting started with your research, solid is way more desirable than super-flexible, and this mount does solid very well.
whitedakota4x4 on October 24, 2009 at 4:04 am
Fantastic quality, This mount is much nicer and stronger then the one I’ve seen at Circuit City for nearly $400.00. Very satisfied.
Jason Lee on October 24, 2009 at 6:09 am
This is a solid, well-made product.It comes with everything you to mount on the wall. It is simple, strong and reasonable price.
I was a little skeptical of this product. I received this wall mount in 3 days. The product worked exacted as stated in desc.
Overall I am very happy and thank AMAZON to help me save money.
J.T on October 24, 2009 at 6:41 am
I have 3 year old 50″ Plasma and decided it to put on the wall when I remodel the room.
I like the dual arms since my TV is old and heavy and dual arms hold my TV more stable. I can pull it away from the wall to access the wires and adjust the left to right when I sit in dinner room. It seems very sturdy and has worked great for my TV. I am very happy with it and said the quality was top notch.